ALPHA6460V Series Special AC Drive for Cross Cutter
ALPHA6460V series special AC drive is exclusively used in cross cutter. In packing and processing industries, there is the cut-to-length process on materials in constant conveying. Conventional cross cut machine consists of PLC and servo system. Cross cut, also known asrotary cut or flying saw, is one of the cut-to-length methods. It allows the material to be vertically cut along its conveying direction. In both packaging and processing industries, the constantly running materials must undergo the cut-to-length process.
ALPHA6460V series realizes the cross cutting by controlling the commonasynchronous motor.It can work in rotary-cut, flying shear, and flying-saw with low system cost, good control performance, wide application,flexible process adjustment, and convenient operation, ALPHA6460V series provides a brand new drive and control solution to cross cutting industry.
Cutting precision: ±3mmat speed of 120m/s
Smooth speed curve: Generate motion track by using high precision electric cam; the speed and Acc. curves varying smoothly
Valid for rotary-cutting, after-cutting and flying cutting
Ten groups of cutting length switchable and can be set during running
Manual & Auto cutting modes
Valid for multi-cutter system; Faster cutting
Valid for color-mark correction; applied in the cutting of compensated printing/ position bias on paper or package bags
Material feeding simulation; easy for testing anddebugging
The special AC drive for cross cutter can be often found in the corrugated paper cutting machine, packaging machinery, color printing presses, flying saws, rolling mills, punching machines, embossing machines, slitters, filling machines, and the high-speed wire and rebar cutting machines, among others.
Technical Specifications of ALPHA6460V
380V ±20% three phases: From 1.5 to 93kW
Rated Input Voltage and Frequency
380V three phases: 50/60Hz
Allowable Input Voltage Range
380V three phases: from 304 to 456V, Voltage unbalance rate of less than 3%, Frequency fluctuation of below ±5%
Rated Output Voltage
From 0 to rated input voltage
Max. Overload Current
G model: 150% for one minute, 180% for 20 seconds
V/F control, Open loop vector control, Close loop vector control
From 0.00 to 650.00Hz (from 3R75GB to 3004GB)
From 0.00 to 400.00Hz (from 35R5GB to 3500G)
Digital command ± 0.01% (from -10℃ to +40℃)
Simulation command ± 0.01% (25℃ ± 10℃)
Preset Frequency Resolution
Digital command 0.01Hz
Simulation command 1/1000 of the maximum frequency
Output Frequency Resolution
Preset Frequency Signal
From 0 to 10V, from 0 to 20mA
From 0.1 to 3600 seconds (The acceleration and deceleration time are set individually.)
The additional braking resistance reaches up to 125%.
Four kinds of fixed V/F characteristics are selectable.
Any V/F characteristic can be preset.
The V/F control with PG is available.
Over-voltage, under-voltage, current limit, over-current, overload, electronic thermal relay, overheating, over-voltage stall, load short circuit, grounding, under-voltage protection, input phase loss, output phase loss, short circuit to ground, interphase short circuit, motor overload protection, etc
From -10℃ to +40℃
From 5 to 95% RH (No condensation)
From -40℃ to +70℃
Indoor (without any corrosive gas)
The altitude is at most 1,000m. There is not any dust, corrosive gas, or direct solar radiation.
Less than 5.9m/s2 (0.6g)
Natural cooling or forced air cooling
ALPHA6460V Selection Table
Motor Power (kW)
Rated Output Current (A)
380V Three Phases
Overall Dimension of ALPHA6460V Series Special AC Drive for Cross Cutter
Frequency Inverter | Drive And Control Solution | Crosscut Control System